Projet: Paramètres d’imprimante 3D ANET A8 avec Klipper
1.Cura
Start GCODE
G28 ;Home tout axes
G90 ;positionnement absolu
G1 Z15.0 F6000 ;Mettre Z à 15mm
G0 Y150 F3000 ; Mettre le plateau au millieu pour ne pas chauffer le moteur en Y
M190 S{material_bed_temperature} ; commencer à chauffer le lit à ce qui est défini dans Cura et WAIT
M109 S{material_print_temperature} ; commencer à chauffer le hotend à ce qui est défini dans Cura et WAIT
; Amorcez l’extrudeuse
G92 E0
G1 F200 E3
G92 E0
End GCODE
M104 S0 ;Définir la température de l’extudeur à 0
M140 S0 ;Définir la température du plateau chauffant à 0
; Rentrer le filament
G92 E1
G1 E-1 F300
G91 ;
G1 Z+5 F3000;//Soulever de 5mm
G90
G28 X0 Y0 ;Home axes X et Y
G0 Y150 F3000; Mettre le plateau au millieu pour récupérer la pièce
M84
2.Klipper
Basic:
Serial Port: /tmp/printer
Replace Connection Panel: coché
Klipper Config Path: ~/printer.cfg
Configuration Reload Command: RESTART
Bed leveling:
Probe Height:0,1mm
Probe Lift:5mm
Probe Feedrate Z:500mm/min
Feedrate X/Y:1500mm/min
Klipper configuration:
|
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 |
# This file contains common pin mappings for Anet A8 printer from 2016 # and 2017. To use this config, the firmware should be compiled for # the AVR atmega1284p. # Note that the "make flash" command does not work with Anet boards - # the boards are typically flashed with this command: # avrdude -p atmega1284p -c arduino -b 57600 -P /dev/ttyUSB0 -U out/klipper.elf.hex # See the example.cfg file for a description of available parameters. [stepper_x] step_pin: PD7 dir_pin: PC5 enable_pin: !PD6 step_distance: .01 endstop_pin: ^!PC2 position_endstop: -37 position_max: 220 position_min: -37 homing_speed: 50 [stepper_y] step_pin: PC6 dir_pin: PC7 enable_pin: !PD6 step_distance: .01 endstop_pin: ^!PC3 position_endstop: -2 position_min: -2 position_max: 220 homing_speed: 50 [stepper_z] step_pin: PB3 dir_pin: !PB2 enable_pin: !PA5 step_distance: .0025 endstop_pin: ^!PC4 position_endstop: 0 position_max: 240 homing_speed: 20 [extruder] step_pin: PB1 dir_pin: PB0 enable_pin: !PD6 step_distance: .0105 nozzle_diameter: 0.400 filament_diameter: 1.750 heater_pin: PD5 sensor_type: ATC Semitec 104GT-2 sensor_pin: PA7 #control: pid #pid_Kp: 2.151492 #pid_Ki: 0.633897 #pid_Kd: 230.042965 min_temp: 0 max_temp: 250 [heater_bed] heater_pin: PD4 sensor_type: ATC Semitec 104GT-2 sensor_pin: PA6 #control: watermark min_temp: 0 max_temp: 130 [fan] pin: PB4 [mcu] serial: /dev/ttyUSB0 [printer] kinematics: cartesian max_velocity: 300 max_accel: 1000 max_z_velocity: 20 max_z_accel: 100 [display] lcd_type: hd44780 rs_pin: PA3 e_pin: PA2 d4_pin: PD2 d5_pin: PD3 d6_pin: PC0 d7_pin: PC1 up_pin: PA1 analog_range_up_pin: 9000, 13000 down_pin: PA1 analog_range_down_pin: 800, 1300 click_pin: PA1 analog_range_click_pin: 2000, 2500 back_pin: PA1 analog_range_back_pin: 4500, 5000 #kill_pin: PA1 #analog_range_kill_pin: 400, 600 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [heater_bed] #*# control = pid #*# pid_kp = 74.207 #*# pid_ki = 1.513 #*# pid_kd = 909.963 #*# #*# [extruder] #*# control = pid #*# pid_kp = 20.824 #*# pid_ki = 0.694 #*# pid_kd = 156.183 |